I was recently offered a free Pelican case, and she seemed too young to die. She was structurally sound, so I felt some plastic surgery would make her look 10 years younger… and it did.
I’ve actually been looking to buy a Pelican case, but since this one came to me for free, I thought it was worth trying to refurbishment. At worst, I could buy a new case later and it would cost me nothing other than my time on the refurb. At best, I’d save a couple of hundred dollars on a new case and help recycle something that might have otherwise found its way to the dumps.
Step 1 – The Initial Cleanup
The bag arrived in a pretty dirty state—not surprising, given it’s been stored outdoors—but I got it for free, so I can’t complain about the condition. The photos below show the original uncleaned state.
I know some people like having this wear and tear on their bags, like a badge or honor, but I don’t feel it’s authentic to walk around with a bag that looks like you’ve trekked across the 4 corners of the Earth unless you actually have.
When the bag has earned this kind of wear and tear with me, it’ll stay on the bag.
First up was to give the case a bit of a cleanup to get rid of the spider webs, dirt and a few live spiders. No, seriously. Quite a few had made the Pelican their home in the various tiny holes in the case, the handle, the hinges and the holes for padlocking the bag.
For those of you who don’t know about Australia, it was engineered by God to kill you at every conceivable turn. 5 meter (18 foot) crocodiles that swim in saltwater, killer jellyfish, and 21 of the 25 most deadly snakes in the world live here—not surprisingly, some of the spiders here are deadly, too.
I started with a bit of a rinse before hitting it with some heavy-duty detergent and a scrubbing brush. Once I had done the initial cleanup, I discovered the plastic color wasn’t as severely faded as I expected. I don’t think it had been left in the sun for extended periods.
The foam was also partially reusable, but I was planning to put in a Trekpak system anyway, so there was no reason to retain the foam.
Structurally, the case was perfect. No cracks or damage. Just a few gouges, and it was a little dented in on the outer cover… probably from having heavier objects on top of it.
Step 2 – Restoring the Colour with a Heat Gun
I wasn’t sure how much luck I would have restoring the colour, so I decided to start with a heat gun; if that didn’t work, I’d give the bumper restore option a go. If you have a heat gun, it’s the cheapest option to trial as it requires no purchase.
I can’t claim my stake as the originator of this idea. I started out by searching for the best way to paint a Pelican, until I discovered this post on Reddit where the suggestion came up.
If you haven’t seen the heat gun technique, there are plenty of videos on YouTube showing it with car bumpers. This video shows the process, although they take it a step further by treating the car with a bumper treatment option.
If you’re too lazy to watch the video, start with a heat gun at low heat—about a third to half power—and take your time. I use the heat gun on an area about two inches in size at a time, moving it back and forth across the two-inch area until that area darkens.
The first patch takes a little longer to darken as the heat gun and the plastic heat up. Subsequent areas are a little quicker. Overall, I’d say it should take about half an hour to do the entire bag, depending on whether you stop to allow one side to cool down.
The heat gun worked very well and has restored most of the darkness.
The image above shows a small area that has been heated compared to the colour of the rest of the case just as I started the process. The photo below is what the final result looks like with just the heat gun treatment. I will take another before-and-after photo when I do the treatment, so both photos are taken under the same conditions.
Next Steps
I have “Forever Black Trim Restorer” on order as I wanted to trial how significant the improvement will be. I’ll treat the case when it arrives and I should be able to show if it makes much of a difference in a “Part 2” post when my Trekpak kit comes.
My choice of product, in this case, isn’t necessarily based on experience. I saw it in a 5-year-old post on advrider.com during my search for potential solutions. I can’t comment on its suitability over other products. If you have anything similar, it would be worth trying first.
This photo was the outcome from that post on advrider so it seems to have fairly similar outcomes to my own experiences with the heat gun. The question now is what sort of impact the combination will have.
I could probably stop without the “Forever Black” treatment. It does look good enough for me to be happy with the outcome, but I have already ordered it, so it seemed pointless to let it go to waste. At least other people reading this will have the opportunity to review my outcome before making the purchase.
After that, I’ll also be adding a Trekpak kit, which I have already ordered and am expecting in the next couple of days.
About the author: Athol Hill is a sports and portrait photographer based in Melbourne, Australia. You can find more of his work on his website or by following him on Instagram. This post was also published here.
#abstract #art #abstractart #abstracters_anonymous #abstract_buff #abstraction #instagood #creative #artsy #beautiful #photooftheday #abstracto #stayabstract #instaabstract
https://ift.tt/31rnBPG
0 Comments